Home 101 Show with David Billings - Product sales and services, download audio, streaming feeds, home repair instructions with video

Total Wood Protectant - TWP 300 Series

	TWP 300 Series Deck & Furniture 1 Gal $49.95 \| 5 Gal $245.00 ORDER BY CALLING (205) 326-6789 or 1-888-SPEC-DEK
1 GALLON	5 GALLON
Recommended for spas, exterior furniture, tree houses/swing sets, hardwood decking, teak & mahogany, wooden doors and shutters. More information on TWP 300 Series

TWP 300 Product Description:
A high performance, high solids, exterior wood finish, which may be applied to obtain a stained or high build, deep gloss finish, depending on application procedures. The transparent natural wood tone finishes supplement and enhance the natural beauty o the woods grain and color. The cured finish has superior UV, water and abrasion resistance. The finish is also extremely resistant to attack from mildew and wood destroying organisms. Although the product exhibits excellent penetration on new and old wood, the cured finish is very resistant to airborne contamination and moisture due to its positive dry nature. It contains 60-65% solids but has no free oil to minimize dirt or soil attachment to treated surfaces. Being a positive dry product, it is also resistant to color rub-off on clothes when properly applied.

TWP 300 is a unique combination of chemicals, protecting and enhancing the natural warmth, beauty, and integrity of new and old wood.
TWP 300 products penetrates deeply into the wood without excessive surface film build, highlighting existing grain patterns" with amazing clarity and warmth.
TWP 300 is specifically formulated for protection against water, sunlight, and surface mildew.
TWP 300 reduces water absorption, the major cause of wood cracking and veneer siding de-lamination.
TWP 300 forms a barrier which resists to intrusion of wood destroying organisms, which all cause structural problems and require wood replacement.
TWP 300 is extremely lightfast, containing “ultraviolet light absorbers”
TWP 300 is more resistant to cracking, peeling or blistering than most surface oriented stains on the market. Warning the natural color, while surface mildew speckles eliminate premature unsightly and black discoloration. Accelerated and natural weathering tests show superior performance compared to conventional clear and semi-transparent wood finishes. Many stains on the market are surface oriented and subject to peeling, blistering and chipping.
TWP 300 service life on properly cleaned, and prepared rough sawn vertical cedar siding is generally three to five years with a two coat application in moderate mold and decay climate zones. Areas in extreme mold and decay zones, Such as Florida and other gulf coastal states, may require an additional service coat on portions of siding facing full sun southern exposure, within the warranty period.
TWP 300 PRODUCT USES: Perfect for old or new decks, outdoor furniture, spas, picnic tables, benches, playground equipment, decks, gazebos, shutters, doors, windows, and boats (teak).

TWP 300 Product Uses:
Perfect for old or new decks, outdoor furniture, spas, picnic tables, benches, playground equipment, decks, gazebos, shutters, doors, windows, and boats (teak).

SURFACE PREPARATION:
NEW WOOD: Sand wood smooth with 150 grit sandpaper or pad to open grain. Rinse surface with 4:1 mix of water and household bleach or wood bleach (best for enhanced color). Rinse thoroughly with water and allow a minimum of 48 hours of good drying conditions before applying TWP ® 300.

OLD WOOD: Rinse surface with 3:1 mix of water and household bleach to remove mildew; use wood bleach to brighten wood and follow with 1500 p.s.i. power washer to remove dead surface fiber. Allow a minimum of 48 hours of good drying conditions before applying TWP 300.

PREVIOUSLY STAINED WOOD: Remove all of the old finish with power washing or paint stripper when necessary. Failure to remove the existing finish will result in a blotchy TWP 300 applications, due to uneven penetration and discoloration of aged finish.

METHOD OF APPLICATION: MIX TWP ® 300 THOROUGHLY BEFORE USING! Apply with brush, roll, spray, and wiping cloth or applicator pad. Do not apply below 50° F, if rain is anticipated with 48 hours or heavy dew is present.

Directions for Use:
STAINED EFFECT: Apply a thin coat of approximately 400-500 sq.ft/gal. with brush, roll or applicator pad. This should minimize sheen development especially on tight, non-absorbing wood grain. Remove excess or puddled material that has not penetrated after 15 minutes with a paint pad or rags. See special precaution for rag disposal.

GLOSS VARNISH LOOK: Apply a thin coat of approximately 400-500 sq.ft/gal; allow drying for 48 hours or until firm and then applying a second thin coat.

DRY TIME:
48-96 hours depending on drying conditions. Drying conditions will vary greatly depending on applied film thickness and weather conditions. Multi coat applications may be "tacky" for up to 30 days. Full cure will begin when surface is tack free.

Thinning and Cleanup:
No thinning required. Use mineral spirits for equipment clean up. Rag Disposal - Lay used rags in a single layer outdoors and allow to air dry for 24 hours. To minimize the chance of spontaneous combustion typical of natural drying oils, place rags in water filled metal container for disposal.

Warning:
This product is toxic to fish. Do not contaminate water by cleaning of equipment or disposal of wastes.

Recommended Finish Appearance:
High traffic and abrasive conditions: Gloss finish procedure provides maximum mark and scratch resistance when treating cedar and redwood horizontal surfaces. On harder woods, either stained or gloss appearance gives excellent results.

Decorative Only: Vertical surfaces may be finished or either stained or have a varnished look effect.

TWP 300 MSDS Sheet
AMTECO -- TWP 300 Series
MATERIAL SAFETY DATA SHEET
HMIS CODES: H F R P
2 2 O G

General Information
Company's Name: AMTECO INC
Company's Street: 815 CASS AVE
Company's City: ST LOUIS
Company's State: MO
Company's Country: US
Company's Zip Code: 63106-5000
Company's Emerg Ph #: 800-969-4811
Company's Info Ph #: 800-969-4811
Date MSDS Prepared: 01APR94
Safety Data Review Date: 05MAY95
Preparer's Company: AMTECO INC
Preparer's St Or P. O. Box: 815 CASS AVE
Preparer's City: ST LOUIS
Preparer's State: MO
Preparer's Zip Code: 63106-5000

Ingredients/Identity Information
Proprietary: NO
Ingredient: MEDIUM ALIPHATIC NAPHTHA (AROMATIC 100), PARAFFIN-NAPTHANES
MINERAL SPIRITS
Ingredient Sequence Number: 02
Percent: 25
NIOSH (RTECS) Number: 1003692SN
CAS Number: 64742-88-7
OSHA PEL: 500 PPM
ACGIH TLV: 100 PPM
Other Recommended Limit: 100 PPM
**Aromatic Hydrocarbon
CAS Number: 64742-95-6
OSHA PEL: 200PPM
ACGIH TLV: 200PPM
**Indicates tocic chemical(s) subject to the reporting requirements of
section 313 of Title III and of 40 CFR 372.***

Physical/Chemical Characteristics
Appearance and Odor: BROWN LIQUID
Boiling Point: 300 - 323F
Vapor Density (Air=1): <1
Specific Gravity: 0.9
Evaporation Rate And Ref: SLOWER THAN ETHER
Solubility In Water: INSOLUBLE

Fire and Explosion Hazard Data
Flash Point: 110F
Flash Point Method: TCC
Lower Explosive Limit: 1
Upper Explosive Limit: 7
Extinguishing Media: FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL
Special Fire Fighting Proc: WEAR FULL PROTECTIVE EQUIPMENT & SELF
CONTAINED BREATHING APPARATUS. WATER MAY BE INEFFECTIVE BUT SHOULD BE USED
TO COOL EXPOSED CONTAINERS.
Unusual Fire And Expl Hazrds: CLOSED CONTAINERS MAY EXPLODE WHEN EXPOSED
TO EXTREME HEAT.

Reactivity Data
Stability: YES
Cond To Avoid (Stability): EXTREME HEAT, SPARKS, OPEN FLAME & OTHER
IGNITION SOURCES
Materials To Avoid: NONE
Hazardous Decomp Products: CO, CO2, SMOKE, OXIDES OF NITROGEN
Hazardous Poly Occur: NO

Health Hazard Data
Route Of Entry - Inhalation: YES
Route Of Entry - Skin: YES
Route Of Entry - Ingestion: YES
Health Haz Acute And Chronic: INHALATION: NASAL & RESPIRATORY IRRITATION/
ASPHYXIATION. EYES: SEVERE IRRITATION. SKIN: MAY LEAD TO EXTRACTION OF
NATURAL OILS W/MILD IRRITATION. INGESTION: GI IRRITATION. ASPIRATION OF
MATERIAL INTO THE LUNGS CAN CAUSE CHEMICAL PNEUMONITIS WHICH CAN BE FATAL.
MAY CAUSE LIVER/KIDNEY DAMAGE & CARDIAC ABNORMALITIES.
Carcinogenicity - NTP: NO
Carcinogenicity - IARC: NO
Carcinogenicity - OSHA: YES
Explanation Carcinogenicity: NONE
Signs/Symptoms Of Overexp: IRRITATION, DIZZINESS, WEAKNESS, FATIGUE,
NAUSEA, HEADACHE, UNCONSCIOUSNESS, ASPHYXIATION, REDNESS, TEARING, BLURRED
VISION, SENSATION OF SEEING HALOS AROUND LIGHTS, VOMITING, DIARRHEA
Emergency/First Aid Proc: INHALATION: MOVE TO FRESH AIR. GIVE CPR IF
NEEDED. SKIN: WASH W/SOAP & WATER. EYES: FLUSH W/WATER FOR 15 MINS.
INGESTION: DRINK 1-2 GLASSES OF WATER TO DILUTE. DON'T INDUCE VOMITING.
OBTAIN MEDICAL ATTENTION IN ALL CASES.

Precautions for Safe Handling and Use
Steps If Matl Released/Spill: REMOVE ALL IGNITION SOURCES. REMOVE W/INERT
MATERIAL.
Waste Disposal Method: INCINERATE IN AN APPROVED FACILITY. DON'T
INCINERATE CLOSED CONTAINERS. DISPOSE OF IN ACCORDANCE W/LOCAL, STATE &
FEDERAL REGULATIONS.
Precautions-Handling/Storing: CLOSE CONTAINERS AFTER EACH USE. KEEP AWAY
FROM HEAT, SPARKS & OPEN FLAME. KEEP CONTAINER TIGHTLY CLOSED.
Other Precautions: DON'T TAKE INTERNALLY. AVOID BREATHING VAPORS. LIQUID
MAY PENETRATE SHOES & LEATHER.

Control Measures
Respiratory Protection: USE NIOSH/MSHA APPROVED RESPIRATOR DEVICE.
Ventilation: REQUIRED TO KEEP VAPOR CONCENTRATION LEVELS BELOW GIVEN TLV
LEVELS
Protective Gloves: REQUIRED
Eye Protection: SAFETY EYEWEAR
Other Protective Equipment: EYE BATH & SHOWERS, CHEMICAL RESISTANT APRON,
BOOTS/OTHER CLOTHING
Work Hygienic Practices: WASH HANDS BEFORE EATING, SMOKING/USING WASHROOM.

Disclaimer
To the best of our knowledge, the information contained herein is accurate.
However, Amteco, Inc. does not assume any liability whatsoever for the
accuracy or completeness of the information contained herein. Final
determination of suitability of any material is the sole responsibility of
the user.