Saturdays 8-10am | 92.1 FM WKUL AWR-2 Clear Acrylic Lacquer Water Repellent
ORDER BY CALLING 1 GALLON Product Description: Spread Rate: Surface Preparation:
Concrete, Masonry and Aggregate Surface Sealer
AWR-2:
$45.00 - 1 Gallon
(205) 326-6789 or 1-888-SPEC-DEK
A water clear 100% acrylic solution surface lacquer sealer for exterior and
interior use on concrete, masonry, and aggregate surfaces. The resin has superior
ultra violet light resistance and does not yellow on exterior exposures. It is
specifically designed for ease of maintenance due the ability to re-dissolve into
itself when re-coating after aging. The film has superior resistance to traffic and
most water and oil based common chemicals. Properly sealed surfaces have excellent
food stain resistance. Available in satin, gloss, and black (for asphalt).
Product Uses:
Decorative and uncolored concrete aggregate finishes, terra cotta tiles, concrete,
interior and exterior concrete floors, bricks, driveways, pre-cast exterior
aggregate construction panels, patio blocks, asphalt, stone, cast limestone
sandstone and stucco.
Physical Properties:
.
AWR 2-2
AWR 2-SAL (VOC Compliant)
Weight per gal.
7.4-7.6 lbs.
10.1-10.4 lbs.
Flash Point
110F
140F
Non Vol. Solids
14.1 - 14.3%
12.1 - 12.4%
VOC
774 gr/liter
493 gr/liter
Main Solvent
SC 100
PerChloroethylene
Clean-Up Sol.
Xylol
Xylol
Apply 2 coats to most surfaces, 3 if extremely porous.
New smooth concrete floors
300-400 sq. ft / gal
Old porous surfaces
175-225 sq. ft / gal
Extremely porous decking and vertical siding
125-175 sq. ft / gal
Pavers
80-100 sq. ft / gal
Cast limestone or cast stone
100-150 sq. ft / gal
Split Face
50-75 sq. ft / gal
Remove dust, grease and oil deposits. New floor installations should age a minimum
of 60 days. Exterior concrete floor surfaces, (particularly new surfaces) which are
steel trowel finished, should be acid etched to insure proper penetration and
adhesion. The surface must be thoroughly raised after etching to remove excess salts.
Surface must be thoroughly dry for 48 hours to prevent peeling. Surface temperature
must be above dew point.
Application:
AWR is best applied by spray in thin surface wetting coats. The first coat in
intended to penetrate deeply and should almost disappear into the substrate. (On
extremely smooth or hard substrate one coat should be enough). The second coat will
re-dissolve the first coat and drive it deeper into the substrate. A uniform slight
sheen might result after the second coat. A third coat may be required on very
porous substrates. The porosity and temperature of the substrate are important
influences on exact amount of sheen obtained and resulting surface wear
characteristics. Porosity of the substrate will determine amount of product needed
for each coat.
CAUTION:
Respirators must be worn when applying these materials. Do not smoke or apply near
open flame. See Material Safety Data Sheet for additional safety handling
information. Surface must be thoroughly dry for 24 hours. If moisture remains,
white spots and/or disbonding may result. Remove spots with Trimethyl benzene
then apply another light coat. If material is applies in a heavy single coat,
peeling, disbonding and premature wear patterns may result. AWR can be applied by
brush, roller or spray. AWR2-SAL can applied in the same manner. If surface
temperature is above 80 degrees F, apply by spray only. Equipment must be
compatible with Penalomethane (equipped with Viton/Teflon and stainless steel
parts).
Roller Application:
Use 3/8" Pronell nap or standard 1/4" nap other for paint roller applications. Apply
the material by pushing the roller up and back in a vertical direction. Do not
apply side to side roll with the broom strokes of the concrete). Roll quickly so as
not to allow product to cure on the surface before penetrating into the substrate.
Allow first coat to dry 2 to 4 hours before applying a second coat.
Spray Applications:
Spray light coat with 50% overlapping strokes. Wait 2 to 4 hours before spraying
second coat. Slight sheen might show after show after second coat is applies.
Uniformity of sheen will depend on the uniformity of the porosity and application
technique. Recommended spray tips and pressure 0.017-0.019, tip orifice at
900-1200 p.s.i. Aft4r 24 hour cure, flood AWR treated surface with water to
ensure water seal. Mark dark area indicating water penetration. After 24-48 hour
dry time, apply AWR to marked areas and repeat process to ensure water seal if
necessary.
DO NOT LEAVE PUDDLES ON HORIZONTAL SURFACES!
Dry Time:
30 min. at 77f. Dry hard; 1-2 hours. Recoat, 2 hours.
Thinning & Cleaning:
Thinning not required except during high temperatures. Thin with 1 qt. xylol per
gallon when surface temperature exceeds 95 degrees. Use xylol for equipment
cleanup.
Additional Info
Recommended for driveways, garage & basement floors, brick, stone & concrete
walkways & patios. Eliminates water, soil & oil absorption into the surface when
properly applied. Available in: satin, glossy or black finishes (glossy & black by
special order only). Mix before using, stir occasionally during use, keep away from
children.
Welcome New Sponsors
Please call, 205.458.1535, for advertisement information