Saturdays 8-10am | 92.1 FM WKUL Clean and Brite CLEANER STRIPPER and DEGREASER
ORDER BY CALLING 1 GALLON About Clean and Brite: Application: KEEP OUT OF THE REACH OF CHILDREN
Clean Brite:
$18.95 - 1 Gallon
(205) 326-6789 or 1-888-SPEC-DEK
Clean and Brite Stripper and Cleaner is a highly concentrated alkaline formulation
designed to quickly clean and restores cedar, asphalt/fiberglass shingles, removes
dirt, pollen, mildew, and algae stains. Cleans pine, cedar, redwood, and cypress.
Restores original color to wood and roofs. Removes old, worn stains and sealers
from wood surfaces prior to application of new finishes. Quickly restores outdoor
weathered and heavily grayed wood surfaces. Clean and Brite will remove gray wood
fiber, failed wood stains, tannin bleeding, water stains, mildew, algae, and
discolored surface fiber from decks, fences, wood siding, and log homes. Use to
restore wood to its natural color and prepares surfaces for re-coating.
Clean and Brite Stripper and Cleaner is manufactured to quickly remove solid color
or semi transparent oil-based stains and water sealers. Clean and Brite Stripper
and Cleaner will also remove damaged and discolored wood fiber from exterior
surfaces such as decks, wood siding and log homes, Vinyl Siding * Fencing * Patios
* Asphalt/Fiberglass Shingles * Slick Concrete Tile * Tile & Grout * Painted
Gutters * Log Cabins * Cedar & Redwood * Gazebos.
Directions:
Clean and Brite Stripper and Cleaner works upon applying. Dilute Clean and Brite
with water up to 9 parts (makes ten gallons). 9:1 will cover 2000 sq. ft. It
stronger mix is needed, use 8:1 to 1:1 mix. For best results a minimum 1500 psi.
water pressure is needed for rinsing; in many cases residential water pressure is
not sufficient to clean roofs. In such cases, use a low pressure,
pressure-washer.
Decks, Siding, Shingles & More:
If paint and wood-paint removal is required use Clean & Brite or BST Stripper.
Heavily weathered wood surfaces may look fibrous after rinsing. Immediately brushing
along the wood grain helps remove the loose fiber to give a smoother finish. Wood
rich in tannin may darken during restoration - this is temporary. Using Top to
Bottom Roof and Deck Stripper to restore wood before a coating of stain or paint
will help even penetration of the coating. The result will be a longer lasting,
even, and natural looking finish. For best results a minimum 1500 psi. water
pressure is needed for rinsing; in many cases residential water pressure is not
sufficient to clean roofs. In such cases, use a low pressure, pressure-washer.
Note that older or badly weathered wood may still be rough or fibrous after
being restored. Some sanding may be required for appearance.
TO CLEAN CEDAR SHAKE ROOF: Follow above instructions. Do not walk on shingles until
rinsed and dried.
TO REMOVE MILDEW, ALGAE, LEAF & DIRT STAINS FROM CONCRETE: Dilute 4:1 with water.
Spray on generous coat, wait 10 minutes, either brush & rinse with hose, or pressure
wash. Will not remove rust or motor oil stains.
TO CLEAN ASPHALT/FIBERGLASS SHINGLES: Spray bad streaks first & again in spraying
in operations. Start spraying at gutter. Work side to side & backwards to crest.
Wait 10 minutes Start rinsing at crest. Wet 6 rows of shingles in front of you.
Wait 5 minutes, rewet & wait 5 more minutes to make rinsing easier, other shingles
will be wet by rinsing process. Hold hose and pressure wand about 12 inches from
roof. On bad streaks hold about 6 inches or you may need to hold closer. Rinsed
shingles can be walked on immediately without slipping. Rinse slowly until water
is clear for a new look roof Avoid gutter overflow. Protect painted, stained &
sealed surfaces from over-spray & runoff.
TO REMOVE BLACK STREAKS FROM PAINTED GUTTERS: Dilute Clean and Brite from 12:1 to
15:1 depending on type of paint and age. Test on a small area for correct mix.
Adjust mix to suit job. Spray surface. Wait 10 minutes pressure wash.
TO REMOVE OLD PAINT, STAIN/SEALER FROM DECK: Spray on 4:1 mix, wait 10 minutes.
Thoroughly wet deck with water, wait 10 minutes and pressure wash off.
Precautions:
If used on painted, stained or sealed surface, test to be sure it will not harm
coating. Continue to dilute with water until safe mix is found. Use rubber gloves
when handling concentrate & mix if skin is sensitive. Wear rubber sole & waterproof
shoes. If heavy accumulation is present, re-spray those areas to get complete
penetration before rinsing. TEST on new & and weathered wood for
discoloration. Sprayed surfaces are slick, walk with care. Keep off bare
aluminum and glass.
Contains Sodium Hydroxide. Keep away from eyes. Wear safety goggles and rubber
gloves. Do not taste, swallow or breathe. When empty, re-seal container tightly and
dispose of carefully.
Welcome New Sponsors
Please call, 205.458.1535, for advertisement information